This prospective, consecutive, multicentre observational registry aimed to confirm the safety and clinical performance of the SpineJack system for the treatment of vertebral compression fractures (VCF) of traumatic origin. We enrolled 103 patients (median age: 61.6 years) with 108 VCF due to trauma, or traumatic VCF with associated osteoporosis. Primary outcome was back pain intensity (VAS). Secondary outcomes were Oswestry Disability Index (ODI), EuroQol-VAS, and analgesic consumption. 48 hours after surgery, a median relative decrease in pain intensity of 81.5% was observed associated with a significant reduction in analgesic intake. Improvements in disability (91.3% decrease in ODI score) and in quality of life (increase 21.1% of EQ-VAS score) were obtained 3 months after surgery. All results were maintained at 12 months. A reduction in the kyphotic angulation was observed postoperatively (−5.4 ± 6.3°; p < 0.001), remained at 12 months (−4.4 ± 6.0°, p = 0.002). No adverse events were implant-related and none required device removal. Three patients (2.9%) experienced procedure-related complications. The overall adjacent fracture rate up to 1 year after surgery was 2.9%. The SpineJack procedure is an effective, low-risk procedure for patients with traumatic VCF allowing a fast and sustained improvement in quality of life over 1 year after surgery.

Ventral screw osteosynthesis is a common surgical method for treating fractures of the odontoid peg, but there is still no consensus about the number and diameter of the screws to be used. The purpose of this study was to develop a more accurate measurement technique for the morphometry of the odontoid peg (dens axis) and to provide a recommendation for ventral screw osteosynthesis. Images of the cervical spine of 44 Caucasian patients, taken with a 64-line CT scanner, were evaluated using the measuring software MIMICS. All measurements were performed by two independent observers. Intraclass correlation coefficients were used to measure inter-rater variability. The mean length of the odontoid peg was 39.76 mm (SD 2.68). The mean screw entry angle α was 59.45° (SD 3.45). The mean angle between the screw and the ventral border of C2 was 13.18° (SD 2.70), the maximum possible mean converging angle of two screws was 20.35° (SD 3.24). The measurements were obtained at the level of 66% of the total odontoid peg length and showed mean values of 8.36 mm (SD 0.84) for the inner diameter in the sagittal plane and 7.35 mm (SD 0.97) in the coronal plane. The mean outer diameter of the odontoid peg was 12.88 mm (SD 0.91) in the sagittal plane and 11.77 mm (SD 1.09) in the coronal plane. The results measured at the level of 90% of the total odontoid peg length were a mean of 6.12 mm (SD 1.14) for the sagittal inner diameter and 5.50 mm (SD 1.05) for the coronal inner diameter. The mean outer diameter of the odontoid peg was 11.10 mm (SD 1.0) in the sagittal plane and 10.00 mm (SD 1.07) in the coronal plane. In order to calculate the necessary screw length using 3.5 mm cannulated screws, 1.5 mm should be added to the measured odontoid peg length when anatomical reduction seems possible. The cross-section of the odontoid peg is not circular but slightly elliptical, with a 10% greater diameter in the sagittal plane. In the majority of cases (70.5%) the odontoid peg offers enough room for two 3.5 mm cannulated cortical screws.

Preoperative NT-proBNP can help identify patients at high risk for adverse long-term outcome after emergency surgery.

CPC demonstrated good biocompatibility and osseointegration in clinical use, with no evidence of inflammation or osteonecrosis. Demineralized areas in CT scans could be a result of remodeling of the cancellous bone in vertebral bodies.

IntroductionRing fixation of C1 can be performed using pedicle screws and a rod in case of unstable Jefferson or lateral mass fractures of C1.Materials and methodsIn a case series of three patients, we stabilized C1 fractures surgically using a modified technique of C1 ring fixation by using monoaxial instead of polyaxial screws. Functional outcome and pain was recorded postoperatively.ResultsIn this very small case series, we observed good results concerning pain and functional outcome. All fractures were bony healed within 13 weeks. In one case, a screw penetrated the spinal canal and had to be repositioned. A mild irritation of C2 nerve root occurred in two cases postoperatively.ConclusionC1 Ring fusion with monoaxial screws provides a good ability to reduce the fracture indirectly by the screws and the rod itself.