We have analyzed and processed a [Formula: see text] nonorthogonal 3D surface reflection seismic data in the Brunswick no. 6 area to better understand the effect of acquisition geometry on the resultant image and to provide 3D information about the main geologic structures hosting the mineralization. The 3D data were processed using a conventional prestack dip moveout (DMO) and poststack migration algorithm with special focus on refraction static corrections, velocity analysis, and DMO corrections that are important for the data recorded in crystalline environment. However, the nonorthogonal nature of the 3D data combined with its narrow-azimuth, irregular offset distributions, and 2D nature of midpoint distribution in common depth point bins resulted in a lower quality seismic image than those observed on a series of 2D seismic profiles collected in the area prior to the 3D data acquisition. 2D wavenumber spectrum of the data suggests acquisition footprint associated with the data. Most of the noise associated with the acquisition footprint manifested itself as short-length, high-amplitude shallow reflections but largely were attenuated using a dip filter running in the wavenumber domain. Various bin size and geometries were tested, and the best result was obtained using rectangular bins aligned in the orientation of the shot lines. The processing results indicated that the highly prospective and mineralized Brunswick horizon is part of a continuous reflective package that could guide future deep mineral exploration in this mining camp.

The Metal Earth project acquired 927 km of deep seismic reflection profiles from August to November of 2017. Seismic data acquired in this early stage of the Metal Earth project benefited greatly from recent advances in the petroleum sector as well as those in mineral exploration. Vibroseis acquisition with receivers having a 5 Hz response (10 dB down) generated records from a sweep signal starting at 2 Hz, sweeping up to 150 Hz or 200 Hz. Not only does this broadband signal enhance reflections from the deepest to the shallowest crust, but it also helps the use of full waveform inversion (e.g., to mitigate cycle-skipping) and related techniques. Metal Earth regional-scale transects using over 5000 active sensors target mineralizing fluid pathways throughout the crust, whereas higher spatial-resolution reflection and full-waveform surveys target structures at mine camp scales. Because Metal Earth was proposed to map and compare entire Archean ore and geologically similar non-ore systems, regional sections cover the entire crust to the Moho in the Abitibi and Wabigoon greenstone belts of the Superior craton in central Canada. Where the new sections overlap with previous Lithoprobe surveys, a clear improvement in reflector detection and definition is observed. Improvements are here attributed to the increased bandwidth of the signal, better estimates of refraction and reflection velocities used in processing, and especially the pre-stack time migration of the data.

A B S T R A C TApproximately 300 hours of ambient noise data were recorded on a grid of receivers covering an area of 4 km 2 over the Lalor Mine, Canada, to test the capability of seismic interferometry to image ore deposits in the crystalline rock environment. Underground mining activities create the main source of ambient noise in the area. Alongside the ambient noise survey, a larger three-dimensional active-source seismic survey was also acquired and used to evaluate the interferometry results. Power spectral density calculations show random ambient noise with a frequency range of 2 Hz-35 Hz. A beamforming analysis identified body waves arriving from the west-northwest (pointing towards the mine) and surface waves propagating from the northeast. The calculated virtual shot gathers retrieved by cross-correlating ambient noise at all receivers were processed following both two-dimensional and three-dimensional approaches using a sequence similar to the one applied to the activesource three-dimensional data. The dip-moveout stacked section reveals a number of events similar to those observed on the processed active seismic sections. In particular, the passive seismic interferometry method is capable to partly image shallowly dipping reflections but did not produce convincing images of steeply dipping reflections. Dip-moveout stacked sections obtained with different cross-correlation time windows indicate that the strength and number of reflections generally increase with longer noise records. However, a few reflections at depth show reduced coherency with longer noise time windows. The passive seismic interferometry results over the Lalor mining area are encouraging, but image quality of the passive survey is lower than the acquired active three-dimensional survey at the area. Future ambient noise surveys with longer offsets, shorter receiver spacing, and wider azimuth distribution are needed in crystalline rock environment to address the potential of the method for mineral exploration.

No abstract

No abstract