Traditional cellulose filter media used for air filtration in vehicle engines are characterized by 99.9% filtration efficiency and accuracy above 2–5 µm. The highest engine component wear is caused by dust grains above 1 µm. Filter media with nanofiber additions provide greater filtration efficiency of dust grains below 5 µm. Filter material selection for vehicle engine air filter is a problem because their manufacturers mainly provide only the structure parameters: pore size, air permeability, and thickness. There is no information about material filtration properties using polydisperse test dust. The manuscript presents methodology and experimental test results of five samples A, B, C, D and E, filter materials differing in their chemical composition and structure parameters. In the first stage, efficiency characteristics φw, filtration accuracy dzmax and the flow resistance Δpw depending on the dust absorption coefficient km of three filter cartridges of each material, A, B, C, D and E, were determined. Then, from each material characteristics of one piece was selected in order to compare their initial and initial period efficiencies as well as changes in the flow resistance depending on the dust absorption coefficient km. Obtained results showed that the filter materials differ significantly in efficiency and accuracy values in the initial filtration period. Initial period duration is also different, i.e., filtration efficiency increasing time to a certain value, which for materials with a nanofiber layer is much shorter, which minimizes engine component wear. For materials with nanofibers, flow resistance increase intensity is greater, which results from surface filtration. Filtration efficiency of each filter material sample A, B, C, D and E was assessed with the filtration quality coefficient including the efficiency and flow resistance. In the available literature, the problem of increasing filtration efficiency in the initial period is known, but there are no results for specific filter materials. Research shows that filter material characteristics are closely related. Each increase in efficiency and accuracy of intake air filtration reduces engine components wear, but it is related to flow resistance increase in the engine intake system, which reduces its power, and increases need for more frequent filter servicing.

This paper systematically reviews the research progress in the field of the influence of air pollutants in the engine inlet on the accelerated wear of the elements of the association: piston, piston rings, cylinder liner (P-PR-CL), and plain bearing (journal–panel). It was shown at the outset that the primary component of air pollution is road dust. Its main components are dust grains of hard minerals (SiO2, Al2O3), which penetrate the oil film area between two frictionally mating surfaces causing their abrasive wear. Therefore, the effect of three dust parameters (grain size and hardness, and dust concentration in air) on the accelerated wear of the friction pair: piston, piston rings, cylinder liner(P-PR-CL), and plain bearing (journal–pan) is presented extensively. It was noted that the wear values of the same component were obtained by different researchers using different testing techniques and evaluated by different indices. It has been shown that the greatest wear of two frictionally cooperating surfaces is caused by dust grains with sizes equal to the thickness of the oil film at a given moment, which in typical combustion engine associations assumes varied and variable values in the range of 0–50 µm. The oil film thickness between the upper ring and the cylinder liner varies and depends on the crankshaft rotation angle, engine speed and load, and oil viscosity, and takes values less than 10 µm. It was shown that the maximum wear of the cylinder liner, resulting from the cooperation with the piston rings, occurs in the top dead centre (TDC) area and results from unfavorable (high temperature, low piston speed) operating conditions of these elements. From the extensive literature data cited, it follows that abrasive wear is caused by dust grains of specific dimensions, most often 5–20 µm, the greater the wear the greater the hardness of the grains and the sulfur content of the fuel. At the same time, it was shown that the main bearing, crankshaft bearing, and oil ring experienced maximum wear by a different range of particle size, respectively: 20–40, 5–10, and 20–80 μm. It was shown that the mass of dust that enters the engine cylinders and thus the wear of the components is determined by the concentration of dust, the value of which is definitely reduced by the air filter. However, it was pointed out that the low initial filtration efficiency and the presence of large dust grains in the purified air in the initial period of the filter operation (after replacement of the filter element with a new one) may have an impact on the accelerated wear of mainly (P-PR-CL) association. The next stage of the paper presents the effects of excessive wear of the cylinder liner and piston rings of the engine, resulting from actual vehicle operation and bench tests on the decrease in compression pressure and engine power, increase in the intensity of exhaust gas blow-by into the oil sump and increase in oil consumption and exhaust gas toxicity. This paper addresses the current problem of the effect of engine inlet air contaminants on the performance of the air flow meter, which is an essential sensor of the modern internal combustion engine. The phenomenon of deposition of contaminants (mineral dust, salt, carbon deposit, and moisture) on the measuring element (wire or layer anemometer) of the air flow meter has been analyzed. The empirical results presented show that the mineral dust layer on the measuring element of the air flow meter causes a 17.9% reduction in output voltage, and the dust and oil layer causes a 46.7% reduction in output voltage. This affects the decrease in engine power and exhaust toxicity.

Pollutant properties in intake air to internal combustion engines were analyzed. Mineral dust particles’ influence on accelerated engine components’ wear was discussed. Dust concentration values in the air under various operating conditions in trucks and special vehicles were presented. The idea and necessity for using two-stage filters, operating in a “multi-cyclone–porous partition” system for vehicles operated in dusty air conditions, are presented. Information from the literature information has been presented, showing that impurities in small grain sizes reduce fiber bed absorbency. It has been shown that such a phenomenon occurs during filter material operation, located directly behind the inertial filter (multi-cyclone), which off-road vehicles are equipped with. It results in a greater pressure drop intensity increase and a shorter proper filter operation period. It has been shown that filter material selection for the motor vehicle air filter requires knowledge of the mass of stopped dust per filtration unit area (dust absorption coefficient km) determined for a given permissible resistance value Δpfdop. It has been shown that there is no information on absorption coefficient values for filter materials operating in a two-stage “multi-cyclone–porous partition” separation system. Original methodology and conditions for determining dust absorption coefficient (km) of a separation partition, operating under the conditions of two-stage filtration, were presented. The following characteristics were tested: separation efficiency, filtration performance, and pressure drop characteristics of three different filtration partitions. These were A (cellulose), B (cellulose and polyester), and C (cellulose, polyester, and nanofibers layer), working individually and in a two-stage system—behind the cyclone. Granulometric dust composition dosed into the cyclone and cyclone downstream was determined. During tests, conditions corresponding to air filter’s actual operating conditions, including separation speed and dust concentration in the air, were maintained. For the pressure drop values, the dust absorption coefficient (km) values of three different filtration partitions (A, B, and C), working individually and in a two-stage system—behind the cyclone—were determined experimentally.

The paper presents the composition of atmospheric air as a mixture of gases that make up the solid and variable components, and the definitions of air pollutants are referenced. Gaseous and solid pollutants (dust) of the atmospheric air have been defined. Dusts were divided according to various criteria and their properties were given. Exemplary courses of immission of the fraction of solid particles are given, indicating a strong dependence of the immission on the seasons, days of the week and day and night. The sources and characteristics of artificial and natural pollutants in the atmospheric air are presented. It has been shown that the main sources of anthropogenic pollution in addition to industry and the automotive industry. Cars are a source of gaseous and particulate pollutants PM, and they also emit pollution from brake and clutch lining wear, as well as from tire and road wear. The main sources of natural air pollution were discussed, including volcanic eruptions, fires in landfills, forests, steppes and sand storms, as well as mineral dust (road dust) carried from the ground by vehicles. The properties of road dust are discussed: chemical and fractional composition, density, dust concentration in the air. It has been shown that the two basic components of the dust, silica and corundum, whose share in dust reaches 95%, also have the highest hardness, which may have a decisive influence on the wear of engine components. Various valuesof dust concentration in the air were presented depending on the type and condition of the ground and the conditions of use of vehicles. Keywords: mechanical engineering, internal combustion engines, air pollution sources, road dust