An inductively coupled plasma (ICP) process was used to synthesize transition metal dichalcogenides (TMDs) through a plasma-assisted selenization process of metal oxide (MO x ) at a temperature as low as 250 °C. In comparison with other CVD processes, the use of ICP facilitates the decomposition of the precursors at low temperatures. Therefore, the temperature required for the formation of TMDs can be drastically reduced. WSe 2 was chosen as a model material system due to its technological importance as a p-type inorganic semiconductor with an excellent hole mobility. Large-area synthesis of WSe 2 on polyimide (30 × 40 cm 2 ) flexible substrates and 8 in. silicon wafers with good uniformity was demonstrated at the formation temperature of 250 °C confirmed by Raman and X-ray photoelectron (XPS) spectroscopy. Furthermore, by controlling different H 2 /N 2 ratios, hybrid WO x /WSe 2 films can be formed at the formation temperature of 250 °C confirmed by TEM and XPS. Remarkably, hybrid films composed of partially reduced WO x and small domains of WSe 2 with a thickness of ∼5 nm show a sensitivity of 20% at 25 ppb at room temperature, and an estimated detection limit of 0.3 ppb with a S/N > 10 for the potential development of a low-cost plastic/wearable sensor with high sensitivity.

High-frequency operation with ultrathin, lightweight, and extremely flexible semiconducting electronics is highly desirable for the development of mobile devices, wearable electronic systems, and defense technologies. In this work, the experimental observation of quasi-heterojunction bipolar transistors utilizing a monolayer of the lateral WSe-MoS junctions as the conducting p-n channel is demonstrated. Both lateral n-p-n and p-n-p heterojunction bipolar transistors are fabricated to exhibit the output characteristics and current gain. A maximum common-emitter current gain of around 3 is obtained in our prototype two-dimensional quasi-heterojunction bipolar transistors. Interestingly, we also observe the negative differential resistance in the electrical characteristics. A potential mechanism is that the negative differential resistance is induced by resonant tunneling phenomenon due to the formation of quantum well under applying high bias voltages. Our results open the door to two-dimensional materials for high-frequency, high-speed, high-density, and flexible electronics.

The experimental observation of band-to-band tunneling in novel tunneling field-effect transistors utilizing a monolayer of MoS as the conducting channel is demonstrated. Our results indicate that the strong gate-coupling efficiency enabled by two-dimensional materials, such as monolayer MoS , results in the direct manifestation of a band-to-band tunneling current and an ambipolar transport.

We demonstrated a promising route to enhance the performance of inverted organic photovoltaic (OPV) devices by the incorporation of CuGaSe2 (CGS) quantum dots (QDs) into the ZnO buffer layer of P3HT:PCBM-based devices. The modification of QDs provides better band alignment between the organic/cathode interface, improves ZnO crystal quality, and increases photon absorption, leading to more effective carrier transport/collection. By employing this energy-harvesting scheme, short-circuit current density, open-circuit voltage, and fill factor of the OPV device after CGS QD modification are improved by 9.43%, 7.02% and 6.31%, respectively, giving rise to a 23.8% enhancement in the power conversion efficiency.

Vertical hot electron transistors incorporating atomically-thin 2D materials, such as graphene or MoS2, in the base region have been proposed and demonstrated in the development of electronic and optoelectronic applications. To the best of our knowledge, all previous 2D material-base hot electron transistors only considered applying a positive collector-base potential (VCB > 0) as is necessary for the typical unipolar hot-electron transistor behavior. Here we demonstrate a novel functionality, specifically a dual-mode operation, in our 2D material-base hot electron transistors (e.g. with either graphene or MoS2 in the base region) with the application of a negative collector-base potential (VCB < 0). That is, our 2D material-base hot electron transistors can operate in either a hot-electron or a reverse-current dominating mode depending upon the particular polarity of VCB. Furthermore, these devices operate at room temperature and their current gains can be dynamically tuned by varying VCB. We anticipate our multi-functional dual-mode transistors will pave the way towards the realization of novel flexible 2D material-based high-density and low-energy hot-carrier electronic applications.