Energy harvesting technologies that are engineered to miniature sizes, while still increasing the power delivered to wireless electronics, (1, 2) portable devices, stretchable electronics, (3) and implantable biosensors, (4, 5) are strongly desired. Piezoelectric nanowire- and nanofiber-based generators have potential uses for powering such devices through a conversion of mechanical energy into electrical energy. (6) However, the piezoelectric voltage constant of the semiconductor piezoelectric nanowires in the recently reported piezoelectric nanogenerators (7-12) is lower than that of lead zirconate titanate (PZT) nanomaterials. Here we report a piezoelectric nanogenerator based on PZT nanofibers. The PZT nanofibers, with a diameter and length of approximately 60 nm and 500 microm, were aligned on interdigitated electrodes of platinum fine wires and packaged using a soft polymer on a silicon substrate. The measured output voltage and power under periodic stress application to the soft polymer was 1.63 V and 0.03 microW, respectively.

Piezoelectric nanocomposites represent a unique class of materials that synergize the advantageous features of polymers and piezoelectric nanostructures and have attracted extensive attention for the applications of energy harvesting and self-powered sensing recently. Currently, most of the piezoelectric nanocomposites were synthesized using piezoelectric nanostructures with relatively low piezoelectric constants, resulting in lower output currents and lower output voltages. Here, we report a synthesis of piezoelectric (1 - x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT) nanowire-based nanocomposite with significantly improved performances for energy harvesting and self-powered sensing. With the high piezoelectric constant (d33) and the unique hierarchical structure of the PMN-PT nanowires, the PMN-PT nanowire-based nanocomposite demonstrated an output voltage up to 7.8 V and an output current up to 2.29 μA (current density of 4.58 μA/cm(2)); this output voltage is more than double that of other reported piezoelectric nanocomposites, and the output current is at least 6 times greater. The PMN-PT nanowire-based nanocomposite also showed a linear relationship of output voltage versus strain with a high sensitivity. The enhanced performance and the flexibility of the PMN-PT nanowire-based nanocomposite make it a promising building block for energy harvesting and self-powered sensing applications.

Direct piezoelectric potential measurement of single lead ziroconate titanate (PZT) nanofiber under bending using a nanomanipulator inside a scanning electron microscope chamber was presented. The PZT nanofibers, with the diameter and length around 100 nm and 70–100 μm, respectively, were aligned across trenches on a silicon substrate with a thermally grown oxide diffusion barrier and evaporated gold electrodes. A potential of ∼0.4 mV was generated when a bending moment was applied to a PZT nanofiber with an effective length of 4 μm by a tungsten tip of the nanomanipulator. The experiment demonstrated the feasibility of using these PZT nanofibers for nanoscale sensing, actuation, and energy harvesting.

A profound way to increase the output voltage (or power) of the piezoelectric nanogenerators is to utilize a material with higher piezoelectric constants. Here we report the synthesis of novel piezoelectric 0.72Pb(Mg(1/3)Nb(2/3))O(3)-0.28PbTiO(3) (PMN-PT) nanowires using a hydrothermal process. The unpoled single-crystal PMN-PT nanowires show a piezoelectric constant (d(33)) up to 381 pm/V, with an average value of 373 ± 5 pm/V. This is about 15 times higher than the maximum reported value of 1-D ZnO nanostructures and 3 times higher than the largest reported value of 1-D PZT nanostructures. These PMN-PT nanostructures are of good potential being used as the fundamental building block for higher power nanogenerators, high sensitivity nanosensors, and large strain nanoactuators.

Aligned piezoelectric (PZT) nanofibres were fabricated by electrospinning using PZT sol–gel as precursor. A pure perovskite phase with an average grain size of 10 nm was obtained at 650 °C. The average diameter of these fibres could be controlled to range from 52 to 150 nm by varying the concentration of poly(vinyl pyrrolidone) (PVP) in the precursor. Special samples of PZT nanofibres were deposited across the microfabricated trenches on a silicon wafer. Atomic force microscopy (AFM) was used to measure the mechanical properties of a single nanofibre. The elastic modulus of an individual PZT nanofibre that was obtained was 42.99 GPa, which was smaller than that of a thin-film PZT. The possible reasons for the reduction in elastic modulus of the nanofibres were discussed.