The food industry nowadays is facing new challenges in terms of sustainability and health implications of packaging and processing techniques. Due to their desire for new and natural products coupled with changes in lifestyle, consumers are looking for food products that have been less processed but possess longer shelf life and maintain nutritional and sensorial proprieties during storage. These requirements represent real challenges when dealing with highly perishable food products, such as fruits and vegetables. Thus, in recent years, edible coatings have been intensively developed and studied because of their capacity to improve the quality, shelf life, safety, and functionality of the treated products. Edible coatings can be applied through different techniques, like dipping, spraying, or coating, in order to control moisture transfer, gas exchange, or oxidative processes. Furthermore, some functional ingredients can be incorporated into an edible matrix and applied on the surface of foods, thus enhancing safety or even nutritional and sensory attributes. In the case of coated fruits and vegetables, their quality parameters, such as color, firmness, microbial load, decay ratio, weight loss, sensorial attributes, and nutritional parameters, which are very specific to the type of products and their storage conditions, should be carefully monitored. This review attempts to summarize recent studies of different edible coatings (polysaccharides, proteins, lipids, and composites) as carriers of functional ingredients (antimicrobials, texture enhancers, and nutraceuticals) applied on different minimally processed fruits and vegetables, highlighting the coating ingredients, the application methods and the effects on food shelf life and quality.

No abstract

Adsorption and thermal desorption dynamics of acetone in fixed bed silica gel were studied experimentally and theoretically. The effect of process factors on adsorption and desorption performances was established. Acetone adsorption from air stream was performed by the dynamic (flowing gas) method in a laboratory set-up at two levels of air superficial velocity (0.7 and 1.7 cm/s), temperature (30 and 40 °C) and adsorbent particle diameter (0.21 and 0.54 cm). The values of saturation adsorption capacity (0.147-0.270 g/g) increased up to 78 % and 36 %, respectively, with a decrease in air velocity and adsorption temperature. Acetone thermal desorption from spent silica gel was studied in a thermobalance at three levels of process temperature (60, 70 and 80 °C) and two values of particle size (0.21 and 0.54 cm). Equilibrium desorption efficiency (63-81 %) was up to 14 % larger for finer particles and increased with the desorption temperature. Kinetic models with relevant parameters adjusted based on experimental data were adopted to predict the dynamics of acetone adsorption and thermal desorption. The models simulated well the real conditions and could be applied to scale up and operate the adsorption columns used for air remediation.

The paper aimed at studying the slow pyrolysis of vine pruning waste in a fixed bed reactor and characterizing the pyrolysis products. Pyrolysis experiments were conducted for 60 min, using CO2 as a carrier gas and oxidizing agent. The distribution of biochar and bio-oil was dependent on variations in heat flux (4244–5777 W/m2), CO2 superficial velocity (0.004–0.008 m/s), and mean size of vegetal material (0.007–0.011 m). Relationships among these factors and process performances in terms of yields of biochar (0.286–0.328) and bio-oil (0.260–0.350), expressed as ratio between the final mass of pyrolysis product and initial mass of vegetal material, and final value of fixed bed temperature (401.1–486.5 °C) were established using a 23 factorial design. Proximate and ultimate analyses, FT-IR and SEM analyses, measurements of bulk density (0.112 ± 0.001 g/cm3), electrical conductivity (0.55 ± 0.03 dS/m), pH (10.35 ± 0.06), and water holding capacity (58.99 ± 14.51%) were performed for biochar. Water content (33.2 ± 1.27%), density (1.027 ± 0.014 g/cm3), pH (3.34 ± 0.02), refractive index (1.3553 ± 0.0027), and iodine value (87.98 ± 4.38 g I2/100 g bio-oil) were measured for bio-oil. Moreover, chemical composition of bio-oil was evaluated using GC-MS analysis, with 27 organic compounds being identified.

The agronomic benefits of biochar (BC) prepared by slow pyrolysis of vine pruning residues, which are produced in large quantities in Romania, were evaluated. Three soil types, i.e., slightly alkaline fluvisol (S1), slightly acidic chernozem (S2), and strongly acidic luvisol (S3), with mean values of pH of 7.99, 6.26, and 5.40, were amended with BC at a volumetric ratio between BC and soil of 20/80. A greenhouse experiment was performed for 109 days to assess the effects of BC amendment on bell pepper growth. The following treatments were applied: foliar fertilizer, BC, BC + foliar fertilizer (using two concentrations of foliar fertilizer solution), and a control. Strongly alkaline BC (pH of 9.89 ± 0.01) had a significant positive effect on the growth performance of bell pepper plants sown in the strongly acidic soil S3. The mean values of height, collar diameter, number of leaves, and root volume of plants grown in BC-amended soil S3 without foliar treatment were significantly higher (13–72% and 14–33%, respectively) than those of plants grown in non-amended soil S3 without and with foliar treatment. This beneficial effect of BC on bell pepper plant growth was due to the changes in the soil properties. BC significantly increased (up to eight times) electrical conductivity, pH, soluble phosphorus, potassium, and ammonium nitrogen concentrations of soil S3, and decreased its bulk density by 51%, resulting in improved water/nutrient uptake and plant growth performance. BC had no favourable effect on the growth parameters of bell pepper plants sown in slightly alkaline soil S1, and slightly acidic soil S2.