The low toxicity and a near-ideal choice of bandgap make tin perovskite an attractive alternative to lead perovskite in low cost solar cells. However, the development of Sn perovskite solar cells has been impeded by their extremely poor stability when exposed to oxygen. We report low-dimensional Sn perovskites that exhibit markedly enhanced air stability in comparison with their 3D counterparts. The reduced degradation under air exposure is attributed to the improved thermodynamic stability after dimensional reduction, the encapsulating organic ligands, and the compact perovskite film preventing oxygen ingress. We then explore these highly oriented low-dimensional Sn perovskite films in solar cells. The perpendicular growth of the perovskite domains between electrodes allows efficient charge carrier transport, leading to power conversion efficiencies of 5.94% without the requirement of further device structure engineering. We tracked the performance of unencapsulated devices over 100 h and found no appreciable decay in efficiency. These findings raise the prospects of pure Sn perovskites for solar cells application.

Tin perovskite is rising as a promising candidate to address the toxicity and theoretical efficiency limitation of lead perovskite. However, the voltage and efficiency of tin perovskite solar cells are much lower than lead counterparts. Herein, indene-C 60 bisadduct with higher energy level is utilized as an electron transporting material for tin perovskite solar cells. It suppresses carrier concentration increase caused by remote doping, which significantly reduces interface carriers recombination. Moreover, indene-C 60 bisadduct increases the maximum attainable photovoltage of the device. As a result, the use of indene-C 60 bisadduct brings unprecedentedly high voltage of 0.94 V, which is over 50% higher than that of 0.6 V for device based on [6,6]-phenyl-C61-butyric acid methyl ester. The device shows a record power conversion efficiency of 12.4% reproduced in an accredited independent photovoltaic testing lab.

Development of tin halide perovskites is limited by the extremely poor stability and high background carrier density. Here, based on a pseudohalogen ''catalyst,'' we fabricated a Sn-based hierarchy structure perovskite in a one-step process, comprising highly parallel-orientation 2D PEA 2 SnI 4 on the surface of 3D FASnI 3 . The hierarchy structure delivers significantly enhanced stability and oxidation resistance in air atmosphere. We then explored hierarchy structure perovskite films in planar structure solar cells and achieved a PCE up to 9.41%. HIGHLIGHTS 2D-quasi-2D-3D hierarchy structure perovskite is fabricated for the first time Removable pseudohalogen acts as a regulator to manipulate tin perovskite structureThe hierarchy structure effectively resists oxidation and increases carrier mobilityThe hierarchy structure tin perovskite solar cells achieve a record PCE of 9.41% Wang et al., Joule SUMMARYThe power conversion efficiency (PCE) of tin perovskite solar cells is impeded by the extremely poor resistance to oxidation and high density of intrinsic Sn vacancies. Herein, we grow a 2D-quasi-2D-3D Sn perovskite film using removable pseudohalogen NH 4 SCN as a structure regulator. This hierarchy structure remarkably enhances air stability resulting from the parallel growth of 2D PEA 2 SnI 4 as the surface layer. We then explore the hierarchy structure perovskite films in planar structural solar cells, which generate a PCE up to 9.41%. The device retains 90% of its initial performance for almost 600 hr. Our results suggest that adding removable NH 4 SCN in a perovskite precursor can significantly improve the stability and photovoltaic performance of Sn perovskite. This finding provides a powerful strategy to manipulate the structure of low-dimensional perovskite in order to enhance the performance of perovskite solar cells.

Contemporary thin-film photovoltaic (PV) materials contain elements that are scarce (CIGS) or regulated (CdTe and lead-based perovskites), a fact that may limit the widespread impact of these emerging PV technologies. Tin halide perovskites utilize materials less stringently regulated than the lead (Pb) employed in mainstream perovskite solar cells; however, even today’s best tin-halide perovskite thin films suffer from limited carrier diffusion length and poor film morphology. We devised a synthetic route to enable in situ reaction between metallic Sn and I2 in dimethyl sulfoxide (DMSO), a reaction that generates a highly coordinated SnI2·(DMSO) x adduct that is well-dispersed in the precursor solution. The adduct directs out-of-plane crystal orientation and achieves a more homogeneous structure in polycrystalline perovskite thin films. This approach improves the electron diffusion length of tin-halide perovskite to 290 ± 20 nm compared to 210 ± 20 nm in reference films. We fabricate tin-halide perovskite solar cells with a power conversion efficiency of 14.6% as certified in an independent lab. This represents a ∼20% increase compared to the previous best-performing certified tin-halide perovskite solar cells. The cells outperform prior earth-abundant and heavy-metal-free inorganic-active-layer-based thin-film solar cells such as those based on amorphous silicon, Cu2ZnSn­(S/Se)4 , and Sb2(S/Se)3.

MnO 2 hollow spheres and hollow urchins are synthesized via a simple hydrothermal process without using any template or organic surfactant. The effect of the reaction time on the microstructure and morphology of samples is observed systemically. Meanwhile, the forming mechanism of hollow-structured R-MnO 2 is carefully investigated by using field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). The results of nitrogen adsorption-desorption experiments and electrochemical measurements show that the product obtained by hydrothermal reaction for 6 h has large specific surface area, uniform pore-size distribution, and excellent capacitance performance, which make it have a potential application as a supercapacitor electrode material.