Dual-functioning displays, which can simultaneously transmit and receive information and energy through visible light, would enable enhanced user interfaces and device-to-device interactivity. We demonstrate that double heterojunctions designed into colloidal semiconductor nanorods allow both efficient photocurrent generation through a photovoltaic response and electroluminescence within a single device. These dual-functioning, all-solution-processed double-heterojunction nanorod light-responsive light-emitting diodes open feasible routes to a variety of advanced applications, from touchless interactive screens to energy harvesting and scavenging displays and massively parallel display-to-display data communication.

Here, we report multilayer stacking of films of quantum dots (QDs) for the purpose of tailoring the energy band alignment between charge transport layers and light emitting layers of different color in quantum dot light-emitting diodes (QD LED) for maximum efficiency in full color operation. The performance of QD LEDs formed by transfer printing compares favorably to that of conventional devices fabricated by spin-casting. Results indicate that zinc oxide (ZnO) and titanium dioxide (TiO2) can serve effectively as electron transport layers (ETLs) for red and green/blue QD LEDs, respectively. Optimized selections for each QD layer can be assembled at high yields by transfer printing with sacrificial fluoropolymer thin films to provide low energy surfaces for release, thereby allowing shared common layers for hole injection (HIL) and hole transport (HTL), along with customized ETLs. This strategy allows cointegration of devices with heterogeneous energy band diagrams, in a parallelized scheme that offers potential for high throughput and practical use.

Mesoporous silica with mean pore size of ∼14 nm was coated by polydimethylsiloxane (PDMS) using a thermal deposition method. We showed that the inner walls of pores larger than ∼8 nm can be coated by thin layers of PDMS, and the surfaces consisting of PDMS-coated silica were superhydrophobic, with water contact angles close to 170°. We used the PDMS-coated silica as adsorbents of various gas-phase chemical warfare agent (CWA) simulants. PDMS-coated silica allowed molecular desorption of various CWA simulants even after exposure under highly humid conditions and, therefore, is applicable as an agent for the preconcentration of gas-phase analytes to enhance the sensitivities of various sensors.

The recent emergence of materials for electronic systems that are capable of programmable self-destruction and/or bio/eco-resorption creates the potential for important classes of devices that cannot be easily addressed using conventional technologies, ranging from temporary biomedical implants to enviromentally benign environmental monitors to hardware secure data systems. Although most previous demonstrations rely on wet chemistry to initiate transient processes of degradation/decomposition, options in "dry transient electronic systems" could expand the range of possible uses. The work presented here introduces materials and composite systems in which sublimation under ambient conditions leads to mechanical fragmentation and disintegration of active devices upon disappearance of a supporting substrate, encapsulation layer, interlayer dielectric and/or gate dielectric. Examples span arrays of transistors based on silicon nanomembranes with specialized device designs to solar cells adapted from commercial components

Recently developed approaches in deterministic assembly allow for controlled, geometric transformation of two-dimensional structures into complex, engineered three-dimensional layouts. Attractive features include applicability to wide ranging layout designs and dimensions along with the capacity to integrate planar thin film materials and device layouts. The work reported here establishes further capabilities for directly embedding high-performance electronic devices into the resultant 3D constructs based on silicon nanomembranes (Si NMs) as the active materials in custom devices or microscale components released from commercial wafer sources. Systematic experimental studies and theoretical analysis illustrate the key ideas through varied 3D architectures, from interconnected bridges and coils to extended chiral structures, each of which embed n-channel Si NM MOSFETs (nMOS), Si NM diodes, and p-channel silicon MOSFETs (pMOS). Examples in stretchable/deformable systems highlight additional features of these platforms. These strategies are immediately applicable to other wide-ranging classes of materials and device technologies that can be rendered in two-dimensional layouts, from systems for energy storage, to photovoltaics, optoelectronics, and others.