Functional active wound dressings are expected to provide a moist wound environment, offer protection from secondary infections, remove wound exudate and accelerate tissue regeneration, as well as to improve the efficiency of wound healing.

No abstract

Conductivity and alignment of scaffolds are two primary factors influencing the efficacy of nerve repair. Herein, conductive composite fibers composed of poly(ɛ-caprolactone) (PCL) and carbon nanotubes (CNTs) with different orientation degrees are prepared by electrospinning at various rotational speeds (0, 500, 1000, and 2000 rpm), and meanwhile the synergistic promotion mechanism of aligned topography and electrical stimulation on neural regeneration is fully demonstrated. Under an optimized rotational speed of 1000 rpm, the electrospun PCL fiber exhibits orientated structure at macroscopic (mean deviation angle = 2.78°) or microscopic crystal scale (orientation degree = 0.73), decreased contact angle of 99.2°± 4.9°, and sufficient tensile strength in both perpendicular and parallel directions to fiber axis (1.13 ± 0.15 and 5.06 ± 0.98 MPa). CNTs are introduced into the aligned fiber for further improving conductivity (15.69-178.63 S m −1), which is beneficial to the oriented growth of neural cells in vitro as well as the regeneration of injured sciatic nerves in vivo. On the basis of robust cell induction behavior, optimum sciatic nerve function index, and enhanced remyelination/axonal regeneration, such conductive PCL/CNTs composite fiber with optimized fiber alignment may serve as instructive candidates for promoting the scaffold-and cell-based strategies for neural repair.

Background There are many shortcomings in traditional prefabricated rehabilitation insoles for symptomatic flatfoot patients. This study investigated the effects of customized 3-dimensional (3D) printed insoles on pressure and comfort of the plantar foot in symptomatic flatfoot patients. Material/Methods Eighty patients with bilateral flatfoot participated in this study. At week 0, patients were randomly assigned into 1 of 2 groups. In the control group, the patients wore standardize shoes with prefabricated insoles; and in the experimental group the patients wore standardize shoes and customized insoles. The Footscan ® system recorded peak pressure, peak force, and peak contact area in 10 areas of the sole at weeks 0 and at week 8. Patients used visual analogue scale scores at week 0 and at week 8 to assess overall comfort of insoles. Results At week 0, compared with the control group, the peak pressure in the metatarsal was significantly lower in the experimental group ( P <0.05) while the peak pressure in the mid-foot was significantly higher than the control group ( P <0.05). At week 8, in the experimental group, the peak pressures in the mid-foot were significantly higher than the control group ( P <0.05). The comfort scores (measured by pain scale) reported by the experimental group were significantly lower than those reported by the control group ( P <0.05). Conclusions Customized 3D printed insoles reduced the pressure on the metatarsals by distributed it over the mid-foot area, thus reduced the damage from symptomatic flatfoot. Customized 3D printed insoles were more effective than prefabricated insoles and offered better comfort for patients with symptomatic flatfoot.

Purpose:Osteoporosis is more likely to cause serious complications after joint replacement, mainly due to physiological defects of endogenous osteogenic cells and the pathological osteoclast activity. It is a feasible solution to design a prosthetic surface interface that specifically addresses this troublesome situation. Methods: A novel "three-dimensional (3D) inorganic-organic supramolecular bioactive interface" was constructed consisting of stiff 3D printing porous metal scaffold and soft multifunctional, self-healable, injectable, and biodegradable supramolecular polysaccharide hydrogel. Apart from mimicking the bone extracellular matrix, the bioactive interface could also encapsulate bioactive substances, namely bone marrow mesenchymal stem cells (BMSCs) and bone morphogenetic protein-2 (BMP-2). A series of in vitro characterizations, such as topography and mechanical characterization, in vitro release of BMP-2, biocompatibility analysis, and osteogenic induction of BMSCs were carried out. After that, the in vivo osseointegration effect of the bioactive interface was investigated in detail using an osteoporotic model. Results:The administration of injectable supramolecular hydrogel into the inner pores of 3D printing porous metal scaffold could obviously change the morphology of BMSCs and facilitate its cell proliferation. Meanwhile, BMP-2 was capable of being sustained released from supramolecular hydrogel, and subsequently induced osteogenic differentiation of BMSCs and promoted the integration of the metal microspores-bone interface in vitro and in vivo. Moreover, the osteoporosis condition of bone around the bioactive interface was significantly ameliorated. Conclusion:This study demonstrates that the 3D inorganic-organic supramolecular bioactive interface can serve as a novel artificial prosthesis interface for various osteogenesis-deficient patients, such as osteoporosis and rheumatoid arthritis.