Real-time measurement of grid connected solar panels based on wireless sensors network

Syafii, .; Rusydi, Muhammad Ilhamdi; Putra, Roni; Putra, Muhammad Hadi

doi:10.1109/icseea.2016.7873574

Cited by 13 publications

(4 citation statements)

References 8 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…A low-cost Arduino voltage sensor module with voltage splitters can be used to measure the output voltage. This module is based on the principle of resistance point pressure, and it can make the input voltage of the red terminal decrease by a factor of 5 from the original voltage [12], [13].…”

Section: Solar Panels and Solar Energymentioning

confidence: 99%

Development of methods for managing energy consumption and energy efficiency in a common system

Aslanova

Abdullayeva

Beloglazov

2023

IJECE

View full text Add to dashboard Cite

<span lang="EN-US">The work aims to analyze and examine renewable energy sources (RES) to develop interconnected energy efficiency and energy consumption management system by integrating the software-defined machine-to-machine (M2M) communication. The article’s objectives include analysis of using RES as alternative raw materials for electricity production, the study of intelligent technologies for integrating RES into monitoring and control systems, research of devices and methods for monitoring energy production and consumption, analysis of sensor application for automation of control systems in the energy sector, a study of data transmission and information processing rates. The study results showed that the data transfer rate was delayed by 6 seconds to process 1,000 MB of information. It has been proven that wind energy can be used most efficiently within a 12-hour daily cycle, in contrast to tidal energy and solar energy. It is shown that due to the cyclical nature of obtaining energy from renewable sources, they do not fully provide energy to a large city, on the basis of which it is necessary to additionally use other energy sources. Three different types of power generation facilities were examined and compared. Wind farms were found to have the highest potential for electricity generation, amounting to 1,600-1,700 kW.</span>

show abstract

Section: Solar Panels and Solar Energymentioning

confidence: 99%

Development of methods for managing energy consumption and energy efficiency in a common system

Aslanova

Abdullayeva

Beloglazov

2023

IJECE

View full text Add to dashboard Cite

show abstract

“…In Abo-Zahhad et al (2016), a wireless sensor network system with XBEE was used and all the monitoring was made using Labview. The same approach was used in Syafii et al (2017), but they focus on a solar panel grid. The system proposed by Ul Hassan et al ( 2019) is a real-time metering for the homes that are going to increase the production and utilization of renewable energy.…”

Section: Literature Reviewmentioning

confidence: 99%

Renewable energy smart sensing system monitoring for off-grid vulnerable community in Colombia

et al. 2021

View full text Add to dashboard Cite

“…The strategic geographical position makes the territory of Indonesia very potential in exploiting development, and the development of energy from solar sources is supported by a very high tropical climate [5]. The main equipment for converting energy from the sun to electrical energy is photovoltaic (PV) or better known as solar panels [6], [7]. PV technology has advantages in environmental factors such as being free of carbon dioxide (CO2) emissions and as sustainable energy for future generations [8]- [10].…”

Section: Introductionmentioning

confidence: 99%

Design visual studio based GUI applications on-grid connected rooftop photovoltaic measurement

et al. 2022

View full text Add to dashboard Cite

This article describes the design of a data system to integrate energy conversion from photovoltaic measurements connected to the power grid. The software used is visual studio, while the hardware uses polycrystalline photovoltaic (PV) with a capacity of 2.08 kW and several sensors that have been integrated into Arduino. Parameter data in measuring the performance of this PV system consists of temperature and humidity sensors to measure the panel surface, direct current (DC) current sensor, DC voltage sensor. To measure the current and voltage sourced from the electricity network, the module (PZEM-004T) is used. Measurements are designed using a graphical user interface (GUI) on a Visual Studio application that has been interfaced through Arduino programming. The data output on the sensor measurement will simultaneously record the circuit that has been connected to the solar panel and then display it visually in the form of tables and graphs in real time with a delay of 1 minute. The results of PV on grid measurements in sunny weather conditions obtained the maximum value of all measurements with a DC voltage of 221 V, while for an alternating current (AC) voltage of 231.60 V, the DC value reached 1827.17 W while the AC power was 1681 W.

show abstract

Real-time measurement of grid connected solar panels based on wireless sensors network

Cited by 13 publications

References 8 publications

Development of methods for managing energy consumption and energy efficiency in a common system

Development of methods for managing energy consumption and energy efficiency in a common system

Renewable energy smart sensing system monitoring for off-grid vulnerable community in Colombia

Design visual studio based GUI applications on-grid connected rooftop photovoltaic measurement

Contact Info

Product

Resources

About