The knee ligaments and patellar tendon function in concert with each other and other joint tissues, and are adapted to their specific physiological function via geometry and material properties. However, it is not well known how the viscoelastic and quasi-static material properties compare between the ligaments. The purpose of this study was to characterize and compare these material properties between the knee ligaments and patellar tendon. Dumbbell-shaped tensile test samples were cut from bovine knee ligaments (ACL, LCL, MCL, PCL) and patellar tendon (PT) and subjected to tensile testing (n = 10 per ligament type). A sinusoidal loading test was performed at 8% strain with 0.5% strain amplitude using 0.1, 0.5 and 1 Hz frequencies. Subsequently, an ultimate tensile test was performed to investigate the stress-strain characteristics. At 0.1 Hz, the phase difference between stress and strain was higher in LCL compared with ACL, PCL and PT (p < 0.05), and at 0.5 Hz that was higher in LCL compared with all other ligaments and PT (p < 0.05). PT had the longest toe-region strain (p < 0.05 compared with PCL and MCL) and MCL had the highest linear and strain-dependent modulus, and toughness (p < 0.05 compared with ACL, LCL and PT). The results indicate that LCL is more viscous than other ligaments at low-frequency loads. MCL was the stiffest and toughest, and its modulus increased most steeply at the toe-region, possibly implying a greater amount of collagen. This study improves the knowledge about elastic, viscoelastic and failure properties of the knee ligaments and PT.

No abstract

Knee ligaments and tendons are collagen-rich viscoelastic connective tissues that provide vital mechanical stabilization and support to the knee joint. Deterioration of ligaments has an adverse effect on the health of the knee and can eventually lead to ligament rupture and osteoarthritis. In this study, the feasibility of near infrared spectroscopy (NIRS) was, for the first time, tested for evaluation of ligament and tendon mechanical properties by performing measurements on bovine stifle joint ligament (N=40) and patellar tendon (N=10) samples. The mechanical properties of the samples were determined using a uni-axial tensile testing protocol. Partial least squares regression models were then developed to determine if morphological, viscoelastic, and quasi-static properties of the samples could be predicted from the NIR spectra. Best performance of NIRS in predicting mechanical properties was observed for toughness at yield point (median Q 2 CV = 0.54, median normalized RM SE CV = 6.1%), toughness at failure point (median Q 2 CV = 0.53, median normalized RM SE CV = 6.6%), and the ultimate strength of the ligament/tendon (median Q 2 CV = 0.52, median normalized RM SE CV = 8.3%). Thus, we show that NIRS is capable of estimating ligament and tendon biomechanical properties, especially in parameters related to tissue failure. We believe this method could substantially enhance the currently limited arthroscopic evaluation of ligaments and tendons.

Mechanical characterization of soft tissues such as ligaments remains challenging. There is variability in the measured material parameters of ligaments, most of which is related to natural tissue variability, but some of it can be a result of using different testing protocols. Generally preconditioning (cyclic loading-unloading) is performed prior to actual tests to reduce the experimental variability. Commonly, preconditioning protocols for ligaments with a small strain level and 10 sinusoidal loading-unloading cycles are used. The effect of preconditioning and its parameters including strain level, number of cycles and number of 1 contributed equally to this study. preconditioning repetitions on the repeatability of tensile stress-relaxation tests are poorly known for knee ligaments. In the present study, forty-eight dumbbell-shaped bovine anterior cruciate ligament (ACL) samples were used to evaluate the repeatability of stress-relaxation response. Different preconditioning protocols with 2% and 6% strain levels and 1, 5 or 10 preconditioning repetitions were applied. After preconditioning, one-step stress-relaxation test was carried out twice with an hour resting period in between the tests. The equilibrium stress showed no systematic bias when only one preconditioning repetition was applied (2.0±3.1% difference and p>0.05 between repeated tests). Systematic bias in the peak-toequilibrium stress ratio was not observed when higher strain level and number of repetitions were used (0.5±1.6% difference and p>0.05 between repeated tests). In conclusion, the commonly used preconditioning protocol is capable of producing repeatable equilibrium stress levels of bovine ACLs from stress-relaxation tests in tension. However, if repeatable peak-to-equilibrium stress ratio is desirable, higher strain and number of preconditioning repetitions are recommended.

No abstract