This work presents a single-stage, inverter-based, pseudo-differential amplifier that can work with ultra-low supply voltages. A novel common-mode stabilization loop allows proper differential operations, without impacting over the output differential performance. Electrical simulations show the effectiveness of this amplifier for supply voltages in the range of 0.3–0.5 V. In particular, a dc voltage gain of 25.16 dB, a gain-bandwidth product of 131.9 kHz with a capacitive load of 10 pF, and a static current consumption of only 557 nA are estimated at VDD = 0.5 V. Moreover, the circuit behavior with respect to process and temperature variations was verified. Finally, the proposed amplifier is employed in a switched-capacitor integrator and in a sample-and-hold circuit to prove its functionality in case-study applications.

No abstract

A discrete-time, switched capacitor integrator is presented. The integrator is based on a two-stage architecture where the first stage converts the input voltage into a charge that is accumulated into the second stage. The main strength of the proposed circuit is a higher dc gain with respect to previous solutions, making it optimal for low-voltage inverter-like integrators. A further advantage is the fact that, in contrast with existing solutions, the output voltage is valid across the whole clock cycle. Theoretical analysis of the circuit is performed to calculate the dependence of the integrator dc gain and input-referred offset voltage on the corresponding parameters of the constituting amplifiers. Discrete-time simulations are performed to estimate the gain and phase error with respect to an ideal integrator. The results of electrical simulations performed on an inverter-like prototype, designed with the UMC 0.18 m CMOS process, are presented to show the impact of non-idealities from the amplifiers and switches.

The design of single-stage OTAs for accurate switched-capacitor circuits involves challenging trade-offs between speed and power consumption. The addition of a Slew-Rate Enhancer (SRE) circuit placed in parallel to the main OTA (parallel-type SRE) constitutes a viable solution to reduce the settling time, at the cost of low-power overhead and no modifications of the main OTA. In this work, a practical analytical model has been developed to predict the settling time reduction achievable with OTA/SRE systems and to show the effect of the various design parameters. The model has been applied to a real case, consisting of the combination of a standard folded-cascode OTA with an existing parallel-type SRE solution. Simulations performed on a circuit designed with a commercial 180-nm CMOS technology revealed that the actual settling-time reduction was significantly smaller than predicted by the model. This discrepancy was explained by taking into account the internal delays of the SRE, which is exacerbated when a high output current gain is combined with high power efficiency. To overcome this problem, we propose a simple modification of the original SRE circuit, consisting in the addition of a single capacitor which temporarily boosts the OTA/SRE currents reducing the internal turn-on delay. With the proposed approach a settling-time reduction of 57% has been demonstrated with an SRE that introduces only a 10% power-overhead with respect of the single OTA solution. The robustness of the results have been validated by means of Monte-Carlo simulations.

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.