Iron oxide (Fe3O4), polydopamine (PDA), and in particular their composites are examples of the safest nanomaterials for developing multifunctional nanodevices to perform noninvasive tumor diagnosis and therapy. However, the structures and performances of Fe3O4-PDA nanocomposites should be further perfected to enhance the theranostic efficiency. In this work, we demonstrate the fabrication of PDA-capped Fe3O4 (Fe3O4@PDA) superparticles (SPs) employing preassembled Fe3O4 nanoparticles (NPs) as the cores. Owing to the collective effect of preassembled Fe3O4 NPs, the superparamagnetism and photothermal performance of Fe3O4@PDA SPs are greatly enhanced, thus producing nanodevices with improved magnetic resonance imaging (MRI)-guided photothermal efficiency. Systematical studies reveal that the molar extinction coefficient of the as-assembled Fe3O4 SPs is 3 orders of magnitude higher than that of individual Fe3O4 NPs. Also due to the high aggregation degree of Fe3O4 NPs, the T2-weighted MRI contrast is greatly enhanced for the SPs with r2 relaxivity of 230.5 mM(-1) s(-1), which is ∼2.5 times larger than that of individual Fe3O4 NPs. The photothermal stability, physiological stability, and biocompatibility, as well as the photothermal performance of Fe3O4 SPs, are further improved by enveloping with PDA shell.
Photothermal therapy using inorganic nanoparticles (NPs) is a promising technique for the selective treatment of tumor cells because of their capability to convert the absorbed radiation into heat energy. Although anisotropic gold (Au) NPs present an excellent photothermal effect, the poor structural stability during storage and/or upon laser irradiation still limits their practical application as efficient photothermal agents. With the aim of improving the stability, in this work we adopted biocompatible polypyrrole (PPy) as the shell material for coating urchinlike Au NPs. The experimental results indicate that a several nanometer PPy shell is enough to maintain the structural stability of NPs. In comparison to the bare NPs, PPy-coated NPs exhibit improved structural stability toward storage, heat, pH, and laser irradiation. In addition, the thin shell of PPy also enhances the photothermal transduction efficiency (η) of PPy-coated Au NPs, resulting from the absorption of PPy in the red and near-infrared (NIR) regions. For example, the PPy-coated Au NPs with an Au core diameter of 120 nm and a PPy shell of 6.0 nm exhibit an η of 24.0% at 808 nm, which is much higher than that of bare Au NPs (η = 11.0%). As a primary attempt at photothermal therapy, the PPy-coated Au NPs with a 6.0 nm PPy shell exhibit an 80% death rate of Hela cells under 808 nm NIR laser irradiation.
A new and efficient defect post-healing method for carbon-based mesoscopic perovskite solar cells was developed via hydrophobic ligand (TOPO) coordination.
This paper describes the detection of volatile organic compounds (VOCs) using an e-nose type integrated microfabricated sensor array, in which each resonator is coated with different supramolecular monolayers: p-tert-butyl calix[8]arene (Calix[8]arene), 2,3,7,8,12,13,17,18-octaethyl-21H,23H-porphine (Porphyrin), β-cyclodextrin (β-CD), and cucurbit[8]uril (CB[8]). Supramolecular monolayers fabricated by Langmuir-Blodgett techniques work as specific sensing interface for different VOCs recognition which increase the sensor selectivity. Microfabricated ultrahigh working frequency film bulk acoustic resonator (FBAR) transducers (4.4 GHz) enable their high sensitivity toward monolayer gas sensing which facilitate the analyses of VOCs adsorption isotherms and kinetics. Two affinity constants (K1, K2) are obtained for each VOC, which indicate the gas molecule adsorption happen inside and outside of the supramolecular cavities. Additional kinetic information on adsorption and desorption rate constants (ka, kd) are obtained as well from exponential fitting results. The five parameters, one from the conventional frequency shift signals of mass transducers and the other four from the indirect analyses of monolayer adsorption behaviors, thus enrich the sensing matrix (Δf, K1, K2, ka, kd) which can be used as multiparameter fingerprint patterns for highly selective detection and discrimination of VOCs.
Organic–inorganic
hybrid halide perovskite materials have
attracted enormous interest in recent years due to their excellent
photovoltaic properties, which are strongly limited by their instability.
Solar cells based on the inorganic perovskite materials have been
developed rapidly and exhibit excellent stability. The crystalline
quality and composition of the perovskite layer play the key role
in the efficiency of solar cells. Among the various film deposition
techniques, pulsed laser deposition has the distinctive advantages
of preparation of thin films of high crystalline quality and close
duplication of the composition of the targets. In the work, we applied
pulsed laser deposition to prepare a CsPbBr3 thin film
that displays good stability in a high-humidity environment. Single
crystalline CsPbBr3 powders were grown first by a solution
method to prepare the target. The CsPbBr3 plasma produced
by focused pulsed laser can permeate into the mesoporous TiO2 layer and distribute uniformly inside. The thickness of mesoporous
TiO2 and CsPbBr3 layers has a critical influence
on device performance. The device with optimization of the layer thickness
can achieve the highest power conversion efficiency of 6.3%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.