The flexible conductive-bridging random access memory (CBRAM) device using a Cu/TiW/Ga2O3/Pt stack is fabricated on polyimide substrate with low thermal budget process. The CBRAM devices exhibit good memory-resistance characteristics, such as good memory window (>105), low operation voltage, high endurance (>1.4 × 102 cycles), and large retention memory window (>105). The temperature coefficient of resistance in the filament confirms that the conduction mechanism observed in the Ga2O3 layer is similar with the phenomenon of electrochemical metallization (ECM). Moreover, the performance of CBRAM device will not be impacted during the flexibility test. Considering the excellent performance of the CBRAM device fabricated by low-temperature process, it may provide a promising potential for the applications of flexible integrated electronic circuits.

The effects of radiation on tungsten doped indium oxide (IWO) thin-film transistors (TFTs) have been well investigated in this Letter. In order to achieve high stability and excellent electrical performance simultaneously even in high ionizing radiation damage ambient, different concentrations of tungsten dopant have been introduced for the TFT device fabrication. It is interesting that the high energy ionizing radiation may significantly increase the conductivity and influence the total concentration of oxygen vacancy in the transparent amorphous oxide semiconductor material, which may be completely different from the traditional radiation damage effect for silicon based CMOS devices. However, that abnormal phenomenon will be effectively suppressed by the powerful carrier suppressor, tungsten, which may have a high oxygen bond dissociation energy. Therefore, IWO devices with a 4% tungsten oxide dopant might be the optimized result even after high dosage ionizing radiation exposure. Hence, it may provide a promising radiation hardness approach to improve both the electrical characteristics and reliability for next generation displays, which can be used in the control system of nuclear power generation or space technology.

This work investigates the resistive switching mechanism in the Cu/TiW/InGaZnO/Al2O3/Pt-based memristor. By introducing the Al2O3 layer, the nanoscale diameter of the Cu filament decreased from 6.51 to 0.83 nm as the current compliance decreases from 1 mA to 50 μA. The resistive switching memory characteristics, such as a large ratio of high-resistance state (HRS)/low-resistance state (LRS) (∼107), stable switching cycle stability (>9 × 102), and multilevel operation, are observed and apparently improved compared to the counterpart of the Cu/TiW/InGaZnO/Pt memory device. These results are attributed to the control of Cu formation/dissolution by introducing the Al2O3 nanolayer at the InGaZnO/Pt interface. The findings of this study can not only improve the performance of the amorphous InGaZnO memristor but also be promising for potential applications of next-generation flat-panel displays in wearable devices.

In this study, indium gallium zinc oxide (InGaZnO [IGZO]) active layer capped with an ultrathin p‐type stannous oxide (SnO) is demonstrated to be a thin film transistor (TFT) for color scanning and photosensing device applications. Typically, the sole IGZO‐based TFT is blind to visible light and hard to be developed for visible light sensing. The combination of IGZO and SnO layers can extend the light detection spectrum into visible light wavelengths and ameliorate the photosensing characteristics. The optical responsivity and signal to noise ratio can even be enhanced from 1.05 × 10−2 to 398.02 A W−1 and from 2.1 × 101 to 6.8 × 105 with at least four orders of magnitude, respectively. With the detailed material analysis and physical model discussed, it suggests that the large amount of additional light‐excited carrier generated in the capping layer is the key factor for the significant improvement. Furthermore, the phenomenon of persistent photoconductivity can be effectively suppressed by its natural recombination under the heterojunction structure without applying charge‐pumping method. The electrical uniformity of the sensor device is also highly potential for the next‐generation displays integrating the photosensing functions.

In this study, hydrogen peroxide (H2O2) cosolvent, which was dissolved into supercritical-phase carbon dioxide fluid (SCCO2), is employed to passivate excessive oxygen vacancies of the high-mobility tungsten-doped indium oxide without any essential thermal process. With the detailed material analysis, the internal physical mechanism of the cosolvent effect or the interaction between the cosolvent solution and supercritical-phase fluid is well discussed. In addition, the optimized result has been applied for the thin film transistor device fabrication. As a result, the device with SCCO2 + H2O2 treatment exhibits the lowest subthreshold swing of 82 mV/dec, the lowest interface trap density of 8.76 × 1011 eV–1 cm–2, the lowest hysteresis of 47 mV, and an excellent reliability and uniformity characteristic compared with any other control groups. Besides, an extremely high field-effect mobility of 98.91 cm2/V s can also be observed, while there is even a desirable positive shift for the threshold voltage. Notably, compared with the untreated sample, the highest on/off current ratio of 5.11 × 107 can be achieved with at least four orders of magnitude enhancement by this unique treatment.