The present paper gives a contribution to a better understanding of the flow at the rim and in the wheel space of gas turbines. Steady state and time-accurate numerical simulations with a commercial Navier-Stokes solver for a 1.5 stage turbine similar to the model treated in the European Research Project ICAS-GT were conducted. In the framework of a numerical analysis, a validation with experimental results of the test rig at the Technical University of Aachen will be given. In preceding numerical investigations of realistic gas turbine rim cavities with a simplified treatment of the hot gas path (modelling of the main flow path without blades and vanes), so called Kelvin-Helmholtz vortices were found in the area of the gap when using appropriate boundary conditions. The present work shows that these flow instabilities also occur in a 1.5 stage gas turbine model with consideration of the blades and vanes. Therefore, several simulations with different sealing air mass flow rates (CW 7000, 20000, 30000) have been conducted. The results show, that for high sealing air mass flow rates Kelvin-Helmholtz Instabilities are developing. These vortices significantly coin the flow at the rim.

The measurement of surface temperatures of hot-gas path components of gas turbines under operating conditions provides a considerable challenge because the complexity of measurements under the prevailing conditions is substantial. The results from temperature measurements from an engine test using Thermal History Paint (THP) are presented here. The sensor material in the THP is an oxide ceramic which is doped with lanthanide ions to make the material luminescent. The properties of the luminescence depend on the temperature of exposure. The paper describes the first application of this technology in an extended, rather than dedicated, engine test in which components in both the hot gas path and the secondary air system were coated with THP. During the test campaign the engine components operated below maximum temperature for extended periods of time, which required a novel approach to the calibration of the paint. An overview over the correspondence between the temperatures measured with the THP, thermal paints and CFD calculations is provided for a sideplate and turbine blade. There is very good correlation between the results of the different methods. For the sideplate, the temperature measured with the THP was within 10K of the CFD calculation. Furthermore, the THP exhibited only minor erosion damage after over 50 hours of engine testing. The high durability and measurement accuracy demonstrate the feasibility of using the THP in extended engine tests.

This paper presents the results of integral heat transfer measurements taken in a square ribbed cooling channel configuration for evaluating heat transfer and turbulent flow characteristics in convective cooled gas turbine blades and draws a comparison with numerical results. The heated section of the channel is either smooth or equipped with 45 ∘ crossed ribs on two opposite walls. The first part of the paper describes the instrumentation and experimental setup in detail. The second part compares the numerical calculations with the experimentally determined results. The turbulent heat transfer is calculated using two common algebraic models and three implemented explicit algebraic models, each time in combination with an explicit algebraic Reynolds stress model. The numerical calculations show that the use of higher-order models for the turbulent heat flux provides a higher accuracy of the heat transfer prediction for both configurations. The best model is able to predict almost all results within the experimental uncertainties.

This paper presents two different numerical methods to predict the thermal load of a convection-cooled gas-turbine blade under realistic operating temperature conditions. The subject of the investigation is a gas-turbine rotor blade equipped with an academic convection-cooling system and investigated at a cascade test-rig. It consists of three cooling channels, which are connected outside the blade, so allowing cooling air temperature measurements. Both methods use FE models to obtain the temperature distribution of the solid blade. The difference between these methods lies in the generation of the heat transfer coefficients along the cooling channel walls which serve as a boundary condition for the FE model. One method, referred to as the FEM1D method, uses empirical one-dimensional correlations known from the available literature. The other method, the FEM2D method, uses three-dimensional CFD simulations to obtain two-dimensional heat transfer coefficient distributions. The numerical results are compared to each other as well as to experimental data, so that the benefits and limitations of each method can be shown and validated. Overall, this paper provides an evaluation of the different methods which are used to predict temperature distributions in convection-cooled gas-turbines with regard to accuracy, numerical cost and the limitations of each method. The temperature profiles obtained in all methods generally show good agreement with the experiments. However, the more detailed methods produce more accurate results by causing higher numerical costs.

The present paper gives a contribution to a better understanding of the emergence of Kelvin-Helmholtz instabilities (KHI) in gas turbines. In an earlier paper of the authors, the occurrence of the KHI’s near the rim cavity of a 1.5 stage gas turbine has been examined by use of CFD methods. It is shown that the KHI’s occur, when the swirl component of the hot gas flow is very strong. Due to the fact, that a high swirl is produced by the guide vanes of the first stage, this matter concerns all common gas turbines. In order to get a basic theoretical background of the emergence of the KHI’s, 2D CFD investigations of the flow behind a splitter plate have been performed showing the development of KHI’s downstream of the splitter plate. To validate the numerical results a comparison to test rig data is used. This shows that the numerical method can simulate the characteristics of the KHI’s. Furthermore, a parameter study is conducted to extract parameters describing the appearance of KHI’s, the vortex periodicity and stability criteria. The main intention of this paper is to deliver “KHI parameters”, which are able to describe the development of the KHI in gas turbine rim cavities.