The main focus of this article was to investigate the potential of natural zeolite adsorbent for the removal of CO 2 and H 2 S in biogas produced from palm oil mill effluent (POME) in fixed-bed column adsorption. The effects of the flowrates and dosage of the adsorbent on the CO 2 adsorption were also studied. The surface area of the adsorbent was determined using the Brunauer, Emmett, and Teller (BET) model, while the pore size distribution was calculated according to the Barrett, Joyner, and Halenda (BJH) model. The morphology of the adsorbent was determined by field emission scanning electron microscopy and energy dispersive x-ray (FESEM-EDX) analysis. Before and after purification, the biogas was analyzed by gas chromatography with a thermal conductivity detector and polydimethylsiloxane as a column. Biogas from the POME, via the anaerobic digestion process, produced 89% CH 4 and 11% CO 2 . The surface and structure of the clinoptilolite zeolites was modified by a strong acid (1M HCl), strong base (1M NaOH), and calcination at 450C, and the surface area of the natural zeolites was reduced up to 16%. The working capability of CO 2 adsorption by the modified zeolites decreased with increasing flow rates (100, 200, and 300 mL/min) of the biogas, with levels of CO 2 at 106,906, 112,237, and 115,256 mg/L. The removal of the CO 2 in the biogas by using adsorbent dosages of 1.5, 2.0, and 2.5 g was 97,878, 97,404 and 93,855 mg/L, respectively. The optimum purification of the biogas occurred under the flow rate of 100 mL/min and adsorbent dosage of 2.5 g. The high working capability of the modified zeolites for the removal of CO 2 in the biogas was a key factor, and the most important characteristic for the adsorbent. The results indicate that clinoptilolite zeolites are promising adsorbent materials for both the purification and upgrading of biogas.

No abstract

This study examined the effects of acid/base activation and chitosan coating on clinoptilolite zeolite as an adsorbent for biogas purification from palm oil mill effluent (POME) using simultaneous absorption-adsorption methods. The effects of chitosan concentration in the clinoptilolite zeolite/chitosan (ZAC) composites were studied to determine the best type of adsorbent for purifying biogas to obtain the highest methane (CH4) concentration: the biogas produced from POME via an anaerobic digestion process had a CH4 concentration of 87% and a carbon dioxide (CO2) concentration of 13%. In this study, the Ca(OH)2 solution was used for the absorption process, and the ZAC composite was used as the adsorbent in the adsorption process. To enhance the adsorption efficiency of the adsorbent when purifying biogas, clinoptilolite zeolite (ZA) was activated using strong acid (HCl) and base (NaOH) in various concentrations (ranging from 1-3 M), calcination at 450°C for 2 h, and coating with chitosan concentrations (ranging from 0.25-1 v/v%). The ZA was coated with chitosan to increase its adsorption efficiency, as chitosan contains high levels of amine and hydroxyl groups that interact with CO2 impurities and form carbamic acid, ultimately producing carbamate salt. The composition of biogas before and after treatment was analyzed using gas chromatography. Overall, the final content of the biogas after the purification process with absorption using the Ca(OH)2 solution and adsorption in a fixed-bed column using the ZAC2-0.5 composite was 0.42% CO2 and 99.58% CH4. The purified biogas had a very high methane gas content; thus, this study's findings suggest that purified biogas can be used as a clean energy source for wider industrial applications.

Aluminum black dross is produced by the secondary smelting process of aluminum. Aluminum black dross is classified as hazardous waste because it is reactive with water and produces substances and gases that are harmful to humans and the environment. Generally, aluminum black dross is managed by landfill method, but because it is produced in large amounts every year, the aluminum black dross needs to be utilized to reduce the impact on the environment. Aluminum black dross consists of large amounts of metal oxide and salts. The amount of metal oxide content in aluminum black dross can be used as raw material. This paper review types of processes for utilizing black dross aluminum as raw material in value-added products. aluminum black dross can be used as alumina, adsorbent, zeolite, composites, geopolymers, refractories, and fillers. By utilizing aluminum black dross waste into various products that have economic value, besides being able to protect the environment, it can also reduce environmental resource use.