Experimental results are presented which show the influence on the secondary flow and its losses by a profile modification of the leading edge very close to the endwall. The investigation was carried out with a well-known turbine profile that originally was developed for highly loaded low pressure turbines. The tests were done in a low speed cascade wind tunnel. The geometrical modification was achieved by a local thickness increase; a leading edge endwall bulb. It was expected that this would intensify the suction side branch of the horse-shoe (hs-) vortex with a desirable weakening effect on the passage vortex. The investigated configuration shows a reduction of secondary losses by 2.1 percent points that represents approximately 50 percent of these losses compared to the reference profile. Detailed measurements of the total pressure field behind the cascade are presented for both the reference and the modified profile. The influence of the modified hs-vortex on the overall passage vortex can be clearly seen. The results of a numerical analysis are compared with the experimental findings. A numerical analysis shows that the important details of the experimental findings can be reproduced. Quantitative values are locally different. The theoretical approach taken cannot yet be used for an exact prediction of the loss reduction. However, the analysis of the interaction and the resulting tendencies are considered to be valid. Hence, theoretical investigations as a guideline for the design of a leading edge bulb at the endwall are a valuable tool.

This paper introduces a new test case for compressor aerodynamics. The dataset is provided for the Dresden four-stage Low-Speed Research Compressor (LSRC), which was put into operation in 1995. The compressor consists of four identical stages, which are preceded by an inlet guide vane. The data set will be provided for the reference blading of the compressor with cantilevered stator vanes. This blading was developed on the basis of the profiles of a middle stage of a high-pressure compressor of a jet engine. This paper makes available the blading geometry as well as a variety of flow field measurement results. This includes the compressor map, selected pressure distributions and other results of flow field measurements with conventional techniques (e.g. Pitot probes, 5-hole probes). Furthermore different aspects of blade row interactions were addressed in this compressor within recent years. The periodical unsteady flow field within a selected rotor blade row was investigated using Laser-Doppler-Anemometry. Further results on the unsteady profile pressures and profile boundary layers will be provided. Supplementary, numerical results will be compared to the experiments. Results are available for several stages of the compressor and different operating points. With this test case a unique database for the aerodynamics in a multistage axial compressor will be provided that can be used for the validation of numerical codes.

This contribution introduces a thermodynamically consistent, fully electro-mechanically coupled micro-mechanical model for ferroelectric materials. Adopting a phase field concept, in which the spontaneous polarization is used as order parameter, a Ginzburg-Landau type theory is formulated for the evolution of the order parameter. The equations are discretized within the scope of the Finite Element Method, and implicit time integration is used to solve the non-linear evolution equation. Examples illustrate the physical meaning of phase field parameters and give an application to multi-axial switching in which experimental results are used for comparison.

Recent investigations have shown a reduction of secondary losses in compressor cascades using a bulb like modification of the profile at the endwall. This paper is focussed on experimental work in comparison of 5 different endwall modifications at a compressor cascade. The cascade is modified near the endwall with a bulb, a medium and a large fillet. The fillet configurations are modified by an axial blunt cut-off at the leading edge. The investigations have been carried out at a profile developed from a hub section of the Dresden Low Speed Research Compressor (LSRC) blade, a compressor profile with a nominal turning of 18 deg. A datum configuration and the 5 other configurations were tested at the Low Speed Cascade Windtunnel (LSCW). For the bulb configuration, an intensified horse shoe vortex was suspected and observed counterrotating to the passage vortex with an influence on its propagation. The interaction of the passage vortex and the suction side profile boundary layer is influenced. The superposition of both is minimized and the losses developing from this effect are significant lower. For the fillet and blunt-fillet configurations, a fillet vortex develops and was observed co-rotating to the passage vortex with an influence on the mentioned interaction as well. Blunt leading edges produce additional losses but the superposition of the growing vortices may reduce the overall losses. The cases show a reduction in losses of 1.9% for 3 deg incidence and a range of 1.2% rise to 1.9% reduction in dependence of the incidence. This equals a reduction of the isolated secondary losses up to 28% with respect to the reference profile. Detailed results of the experiments are presented for the reference and all modified cascades.

The present paper describes the design of a new set of blades for the four-stage axial-flow low-speed research compressor (LSRC) at the TU Dresden. The compressor contains nine blade rows: IGV, four rotors and four cantilevered stators designed as repeating stages. The compressor was originally designed and built in the German AG Turbo project. In recent years fourteen builds of the compressor were built and tested [1]. The new design of the NGV (Build A15) has increased pressure ratio and loading compared to the previous builds. The design was performed using a method giving three-dimensionally optimised blades achieving better efficiency than the previous builds with sufficient operating range despite increased loading. The numerical analysis was carried out using a Rolls-Royce 3D-Navier-Stokes solver at design and off-design inlet conditions. The experimental investigations were carried out by the Technical University of Dresden. Overall performance was measured for different speeds and different back-pressures up to compressor stall. Flow field details were measured at a design and a close-to-stall condition using static pressure probes on the blade suction and pressure surface and secondary flow measurements using 5-hole probes.