The technology of tissue engineering is a rapidly evolving interdisciplinary field of science that elevates cell-based research from 2D cultures through organoids to whole bionic organs. 3D bioprinting and organ-on-a-chip approaches through generation of three-dimensional cultures at different scales, applied separately or combined, are widely used in basic studies, drug screening and regenerative medicine. They enable analyses of tissue-like conditions that yield much more reliable results than monolayer cell cultures. Annually, millions of animals worldwide are used for preclinical research. Therefore, the rapid assessment of drug efficacy and toxicity in the early stages of preclinical testing can significantly reduce the number of animals, bringing great ethical and financial benefits. In this review, we describe 3D bioprinting techniques and first examples of printed bionic organs. We also present the possibilities of microfluidic systems, based on the latest reports. We demonstrate the pros and cons of both technologies and indicate their use in the future of medicine.

Crosslinking with 405 nm is better for pancreatic islets than crosslinking with 365 nm UV light. Materials Pancreatic islets Porcine pancreas was digested with collagenase NB8 (Nordmark, S1745602) and then was cultured for 24 h in CMRL 1066 (Gibco, 21530-027) with 10% FBS (EUR X Molecular Biology Products, E5050-03), 100 IU/mL penicillin and 100 μg/mL streptomycin (Corning, 30-002-Cl) and 5 mM glucose (Sigma Aldrich, G8270), in 37˚C and 5% CO 2. Three cell lines were used for the study. Alpha cells αTC1.6-alphaTC1 Clone 6-alpha cell from pancreas of the Mus musculus diseased on adenoma. This cell line was a gift from A. Dobrzyń,

Background: 3D bioprinting is the future of constructing functional organs. Creating a bioactive scaffold with pancreatic islets presents many challenges. The aim of this paper is to assess how the 3D bioprinting process affects islet viability. Methods: The BioX 3D printer (Cellink), 600 μm inner diameter nozzles, and 3% (w/v) alginate cell carrier solution were used with rat, porcine, and human pancreatic islets. Islets were divided into a control group (culture medium) and 6 experimental groups (each subjected to specific pressure between 15 and 100 kPa). FDA/PI staining was performed to assess the viability of islets. Analogous studies were carried out on α-cells, β-cells, fibroblasts, and endothelial cells. Results: Viability of human pancreatic islets was as follows: 92% for alginate-based control and 94%, 90%, 74%, 48%, 61%, and 59% for 15, 25, 30, 50, 75, and 100 kPa, respectively. Statistically significant differences were observed between control and 50, 75, and 100 kPa, respectively. Similar observations were made for porcine and rat islets. Conclusions: Optimal pressure during 3D bioprinting with pancreatic islets by the extrusion method should be lower than 30 kPa while using 3% (w/v) alginate as a carrier.

No abstract

This work is the first attempt to evaluate suitability of Callitriche cophocarpa Sendtn. (water-starwort) to remove Cr under realworld conditions. Our earlier laboratory-scale studies demonstrated outstanding hyperaccumulation properties of this aquatic higher plant (macrophyte) toward chromium in solution. We introduced C. cophocarpa plants into the watershed with sediments heavily polluted (on average 1400 mg/kg d.w. of Cr) by a tannery. The plants grew vigorously and exhibited no physiological or anatomical disorders. Based on chemical fractionations of bottom sediments, we found low Cr bioavailability. The element was strongly associated with the sediments and could be classified into the following fractions (%): oxidizable III (68.2) > residual IV (28.8) > reducible II (1.6) > exchangeable I (1.4). Despite this, Cr content in plant organs at the contaminated sites was 33 up to 83 times greater than in the control leaf/stem and roots, respectively. Altering redox potential during, i.e., sediment deposition on land may change chemical forms of bound metals in a solid phase, and thus further increase Cr phytoextraction by plants. With this in mind, we concluded that the species, being an outstanding Cr accumulator under laboratory conditions, can be useful in the reclamation of Cr-polluted sediments under controlled, oxidizing conditions.