Background: Recently a greater interest in tissue engineering for the treatment of large bone defect has been reported. The aim of the present systematic review and meta-analysis was to investigate the effectiveness of dental pulp stem cells and synthetic block complexes for bone defect treatment in preclinical in vivo articles. Methods: The electronic database and manual search was conducted on Pubmed, Scopus, and EMBASE. The papers identified were submitted for risk-of-bias assessment and classified according to new bone formation, bone graft characteristics, dental pulp stem cells (DPSCs) culture passages and amount of experimental data. The meta-analysis assessment was conducted to assess new bone formation in test sites with DPSCs/synthetic blocks vs. synthetic block alone. Results: The database search identified a total of 348 papers. After the initial screening, 30 studies were included, according to the different animal models: 19 papers on rats, 3 articles on rabbits, 2 manuscripts on sheep and 4 papers on swine. The meta-analysis evaluation showed a significantly increase in new bone formation in favor of DPSCs/synthetic scaffold complexes, if compared to the control at 4 weeks (Mean Diff: 17.09%, 95% CI: 15.16–18.91%, p < 0.01) and at 8 weeks (Mean Diff: 14.86%, 95% CI: 1.82–27.91%, p < 0.01) in rats calvaria bone defects. Conclusion: The synthetic scaffolds in association of DPSCs used for the treatment of bone defects showed encouraging results of early new bone formation in preclinical animal studies and could represent a useful resource for regenerative bone augmentation procedures

The treatment of peri-implantitis implies the decontamination of the surface of the fixture. This study aims to analyze the effect of the erbium-doped yttrium aluminum garnet laser (Er: YAG) on sandblasted and acid-etched (SLA) titanium. 30 titanium SLA disks were divided into three groups. In Group 1, the disks were left intact; on the contrary, both Groups 2 and 3 were irradiated with the Er: YAG laser at different settings, with a pulse duration of 300 μs and a period of 30 s. Group 2 was irradiated at 1 W and 100 mJ/pulse and Group 3 at 4 W and 400 mJ/pulse. The superficial changes at chemical, nano, and microscopical levels were detected through the use of Fourier-transform infrared spectroscopy, atomic force microscopy, and scanning electron microscope. The Kruskal–Wallis test, followed by the Dunn–Bonferroni Post Hoc analysis, detected the presence of statistically significant differences among the groups. The level of significance was p ≤ 0.05. Results showed that Er: YAG irradiation promoted a significant (p < 0.05) increase of oxides and a decrease of microscopical roughness and porosity on SLA disks. However, the protocol tested on group 3 seemed to be too aggressive for the titanium surface, as shown by the presence of micro-cracks and signs of coagulation, melting, and microfractures. In conclusion, Group 2 showed significantly minor surface alterations with respect to Group 3, and the increase of superficial oxide level, the decrease of porosity, and micro-roughness represent a positive alteration that could protect the materials against bacterial adhesion.

No abstract

High bone–implant contact is a crucial factor in the achievement of osseointegration and long time clinical success of dental implants. Micro, nano, microtopography, and oxide layer of dental implants influence tissue response. The lasers were used for achieving an implant surface with homogeneous micro texturing and uncontaminated surface. The present study aimed to characterize the implant surfaces treated by Nd: DPSS Q-sw Laser treatment compared to machined implants. A total of 10 machined implants and 10 lasered surface implants were evaluated in this study. The implant surfaces were evaluated by X-ray Photoelectron Spectroscopy (XPS), Auger Electron Spectroscopy (AES), and metallography to characterize and measure the thickness of the oxide layer on the implant titanium surface. The machined surfaces showed a non-homogeneous oxide layer ranging between 20 and 30 nm. The lasered implant surfaces showed a homogeneous oxide layer ranging between 400 nm and 460 nm in the area of the laser holes, while outside the layer, thickness ranged between 200 nm and 400 nm without microcracks or evidence of damage. Another exciting result after this laser treatment is a topographically controlled, repeatable, homogeneous, and clean surface. This technique can obtain the implant surface without leaving residues of foreign substances on it. The study results indicate that the use of Nd: DPSS Q-sw laser produces a predictable and reproducible treatment able to improve the titanium oxide layer on the dental implant surface.

No abstract